Clog Zapper Enteral Feeding Tube Declogger Kit - 10/Case

The CLOG ZAPPER removes clogs in enteral feeding devices. It combines an “enzyme cocktail”, antimicrobial agents, buffers, metal inhibitors and acids in a ready-to-use system that will unclog your enteral feeding tubes. The CLOG ZAPPER may save valuable time and money by using its pre-mixed, pre-measured and pre-loaded system.

Ready-to-Use System

CLOG ZAPPER contains ingredients that work together to loosen, break down and dislodge clogs. In clinical usage, CLOG ZAPPER was successful in restoring patency to feeding tubes clogged with enteral formulas over 75% of the time.

Nine times more effective in declogging the feeding tubes than flushing alone, the CLOG ZAPPER is efficient and cost-saving.

Features

• Eliminates costly reinsertion and placement confirmation charges.
• Ingredients all work together to loosen, break down and dislodge clogs.
• Saves valuable time by utilizing this pre-mixed, pre-measured and pre-loaded system.
• Comes in a ready to use convenient kit with 2-10 mL oral syringes, and 12 Inch applicator.

Indications for Use

CLOG ZAPPER Enteral Feeding Tube Declogging System is used to clear certain types of blockages, primarily enteral feeding formulations, which may occur in enteral feeding tubes.

Warning: Not for IV use. For enteral use only.

For Single Patient Use.

Storage Requirements: CLOG ZAPPER, once reconstituted, should be used within 24 hours. Refrigerate mixture while not in use.

Caution: Protective eyewear is strongly suggested. CLOG ZAPPER can cause irritation if it gets in contact with the eyes.

Recommendations

• Prior to using CLOG ZAPPER, make sure any visible tubing is free of kinks.
• USE SYRINGES FOUND IN KIT.
• Depending on the location of the clog in the feeding tube, the Applicator might not reach it. THIS IS OK. CLOG ZAPPER will find and clear the obstruction.
• Use CLOG ZAPPER upon FIRST acknowledgement of a CLOGGED tube to maximize the success of CLOG ZAPPER!
• Check to see if patient is allergic to food-based ingredients .
• Use the included 4 in. x 4 in. gauze pads to clean up any spills caused by the Applicator or syringes.
• Always check to see if patient is on a water restricted intake program.
• Amount of fluid used should always be recorded in patient’s intake/output volumes.
• CLOG ZAPPER might not work on some clogs resulting from certain medications. Remember to use liquid medications if possible; crush pills thoroughly. It is not recommended to use enteric coated pills in feeding tubes.

Ingredients

• Papain
• Cellulase
• Maltodextrin
• Ascorbic Acid
• Alpha-Amylase
• Potassium Sorbate
• Disodium Salt EDTA
• Citric 1 Acid Hydrate
• Sodium Lauryl Sulfate
• Disodium Phosphate-Dihydrate
• Contains Tree Nuts (Coconut)

Instructions for NG and J-Tube Use

• Turn feeding pump OFF and close roller clamp on administration set.
• Remove Y-Adapter cap and insert CLOG ZAPPER Applicator Tubing into feeding tube.
• If it is not possible to place the applicator all the way into the feeding tube, the distal end of the applicator may be pressing against the clog. If this is the case, take out the applicator and trim the applicator tubing to the appropriate length. Do not try to break up the clog with the distal end of the applicator.
• Remove syringe cap and fill the CLOG ZAPPER* Syringe to 10 ml mark with water.
• Replace syringe cap and shake vigorously for 3-5 minutes until all powder is dissolved.
• Gently fill tube with recommended dosage of 2-5 ml of CLOG ZAPPER solution.
• Remove applicator from tube. Plug tube (Keep APPLICATOR and SYRINGE together with patient if procedure must be repeated.)
• Keep solution in tubing for 60 minutes / 30 minutes minimum.
• Fill oral syringe with 6 ml of water
• FLUSH! with 6 ml of WATER. After tube clears, dispose per institution’s protocol and resume feeding.

Note: If tubing cannot be flushed, REPEAT steps thru . Always check with physician to determine how many times the process can be repeated.

Instructions For G-Tube Use

• Cut APPLICATOR at dot.
• Discard excess tubing.
• Place APPLICATOR into G-TUBE’s Administration Set port.
• Continue with NG TUBE INSTRUCTIONS above.

Instructions For Low Profile Devices

• Place FEEDING SET into LOW PROFILE DEVICE following manufacturer’s instructions.
• Place APPLICATOR into FEEDING SET.
• Continue with NG TUBE INSTRUCTIONS above.

• The product warranty is applicable as per the terms and conditions provided by the product manufacturer.

Please call us for specific details.

• No returns will be accepted after 30 days from the date of shipment.
• All returns are subject to a restocking fee as per manufacturers terms and conditions.
• All returns must have an RGA number (Returned Goods Authorization), unauthorized returns will not be accepted.
• We do not guarantee fulfillment of any desired purpose or product suitability to the user and this will not be considered as a valid reason for return.
• The products must be new, unused condition, not tampered with, in original packaging and returned at the customers expense in the original packaging.
• If your return is not due to any manufacturing defect then the original shipping cost will be deducted from the total refund.
• Hygiene, bath and toilet items cannot be returned once opened or used.
• Standard manufacturer terms and conditions apply for return policy of this product.

Please call us for specific details.